Titlebook: Recent Advancements in Mechanical Engineering; Select Proceedings o T. S. Sudarshan,K. M. Pandey,Swapan Bhaumik Conference proceedings 2023

神像之光環

書目名稱Recent Advancements in Mechanical Engineering影響因子(影響力)




書目名稱Recent Advancements in Mechanical Engineering影響因子(影響力)學科排名




書目名稱Recent Advancements in Mechanical Engineering網絡公開度




書目名稱Recent Advancements in Mechanical Engineering網絡公開度學科排名




書目名稱Recent Advancements in Mechanical Engineering被引頻次




書目名稱Recent Advancements in Mechanical Engineering被引頻次學科排名




書目名稱Recent Advancements in Mechanical Engineering年度引用




書目名稱Recent Advancements in Mechanical Engineering年度引用學科排名




書目名稱Recent Advancements in Mechanical Engineering讀者反饋




書目名稱Recent Advancements in Mechanical Engineering讀者反饋學科排名

樹木心

Mechanical Properties, Microstructural and Surface Topography Evaluation of AlSi10Mg Alloy Produced.11?J/mm., it showed very few pores and almost negligible balling formation. The above analysis revealed that surface topography also had an impactful role in determining the density of the component. This study also showed an interrelation between relative density and tensile strength of the alloy;

Semblance

Protein

,Microbial Fuel Cell—A Review,ferent separators on the MFC output, also to understand the MFC performance under different operational conditions. In case of dual chamber MFC, performance significantly shows variation when electrode spacing is reduced. Use of 4-layered PTFE diffusion layer in carbon cloth cathode for single-chamb

狼群

Effect of Electrode Length and AC Frequency on Mixing in a Diamond-Shaped Split-And-Recombine Electfor different electrode lengths is different. It is found from the results that the increase in electrode length does not always increase the mixing efficiency of the micromixer. The electrode length of such mixers critically affects the mixing efficiency and the suitable electrode length results in

臨時抱佛腳

Performance Analysis of Split Circular and Drop-Form Fin Geometry for Enhanced Heat Transfer Rate,ar fin. Further, the transverse offset of . and . width has been made in both the circular and drop-form fin shape. Results shows, that the thermal enhancement factor is 13% higher for drop-form split at .?=?. width in comparison with circular fin geometry within the considerable amount of frictiona

Priapism

,Effects of Thermal Aspect Ratio on MHD Thermal Convection of Cu–Water Nanofluid Saturated Porous Cae modified Rayleigh number (Ra.), the permeability of the porous matrix (using Darcy number, Da), the strength of the magnetic field (using Hartmann number, Ha), nanofluid volume fraction (.) and thermal aspect ratios (.). The thermal behavior of these cases is analyzed systematically and illustrate

完成才能戰勝

Stochastic First-Ply Failure Analysis of Laminated Composite Plate: A Moving Least Square Approach,lized as the surrogate model. It is further validated with MCS. Probability density function (PDF) and scatter plot are utilized to depict the validation of the MLS model with MCS. The results further verify that the computationally efficient MLS model can be utilized in place of MCS for further ana

TIA742

Exclaim

Effect of Nano Alumina Reinforcements on the Tribological Behavior of Electroless Nickel-Phosphorusthree. Besides this, the present research also compares the coating with respect to their scratch hardness and micro-Vicker hardness. This research also includes a characterization study of the as-deposited reinforced coating surface via X-ray diffractometry and Scanning electron microscopy (SEM).