Titlebook: Industrial Measurements in Machining; Grzegorz M. Królczyk,Piotr Nies?ony,Jolanta Królcz Conference proceedings 2020 Springer Nature Switz

只看該作者 · 發表于 2025-3-21 19:31:46

書目名稱Industrial Measurements in Machining影響因子(影響力)

書目名稱Industrial Measurements in Machining影響因子(影響力)學科排名

書目名稱Industrial Measurements in Machining網絡公開度

書目名稱Industrial Measurements in Machining網絡公開度學科排名

書目名稱Industrial Measurements in Machining被引頻次

書目名稱Industrial Measurements in Machining被引頻次學科排名

書目名稱Industrial Measurements in Machining年度引用

書目名稱Industrial Measurements in Machining年度引用學科排名

書目名稱Industrial Measurements in Machining讀者反饋

書目名稱Industrial Measurements in Machining讀者反饋學科排名

只看該作者 · 發表于 2025-3-21 23:52:09

只看該作者 · 發表于 2025-3-22 03:52:07

978-3-030-49909-9Springer Nature Switzerland AG 2020

只看該作者 · 發表于 2025-3-22 08:12:15

只看該作者 · 發表于 2025-3-22 11:14:05

Grzegorz M. Królczyk,Piotr Nies?ony,Jolanta KrólczDescribes new theories in machining and metrology.Discusses a number of theoretical and experimental issues.Reports on emerging optimization and control methods

只看該作者 · 發表于 2025-3-22 16:47:10

只看該作者 · 發表于 2025-3-22 17:03:34

Mathematical Modelling of Core Roughness Depth During Hard Turning,ter and coefficient . obtained from the ratio between . and the sum of . and .. According to the obtained mathematical models, 3D graphs of the dependences between the . parameter, coefficient . and the input independent variables are also shown. The obtained mathematical models are explained, and a

只看該作者 · 發表于 2025-3-23 00:03:04

只看該作者 · 發表于 2025-3-23 01:55:04

The Surface Texture of Ti6Al4V Titanium Alloy Under Wet and Dry Finish Turning Conditions,e cutting speed and feed rate influence are lower in comparison with wet turning. Compared to wet machining, a higher number of surface defects caused by adhesive bonds were observed under dry turning. Favorable values of roughness parameters were obtained using middle cutting speeds and feed rates

只看該作者 · 發表于 2025-3-23 06:27:18

		自動登錄	找回密碼
密碼			To register

關于派博傳思			派博傳思旗下網站			友情鏈接
派博傳思介紹	公司地理位置	論文服務流程	影響因子官網	吾愛論文網	大講堂	北京大學	Oxford Uni.	Harvard Uni.
發展歷史沿革	期刊點評	投稿經驗總結	SCIENCEGARD	IMPACTFACTOR	派博系數	清華大學	Yale Uni.	Stanford Uni.
\|Archiver\|手機版\|小黑屋\| 派博傳思國際 ( 京公網安備110108008328) GMT+8, 2026-1-21 20:26
Copyright © 2001-2015 派博傳思京公網安備110108008328 版權所有 All rights reserved